Chain Replacement for Husqvarna 350 Chainsaw: 5 Steps in Detail!

Want to know how to change the chain on a Husqvarna 350 chainsaw? The process is easy as pie. Simply pull out the cover, a few screws, and the old chain with a new one. Reassembling everything will complete the process. Simple, huh?

Well, if you don’t know how to perform all of this correctly, it could be challenging. However, don’t panic; this post will cover how it can be accomplished swiftly. You will be able to replace the chain on your own at the end of this article.

Husqvarna 350 Chainsaw Chain Replacement in 5 Easy Steps

Husqvarna 350 Chainsaw Chain Replacement
Husqvarna 350 Chainsaw Chain Replacement

It’s very easy to change the chain on a Husqvarna 350 chainsaw. You won’t have the smallest trouble changing the chain on your own if you can follow the simple instructions listed below.

However, you ought to have a few things close at hand before diving in. You require these tools to change the chain on a Husqvarna chainsaw.

What You’ll Need

Step 1: Get the chainsaw ready

The chainsaw needs to be set up correctly as the first step. Place it on a level surface. Make sure there are no edges near where you are placing the machine.

After the chainsaw has been properly positioned, remove the spark plug’s boot. This will stop the device from turning on by accident.

Last but not least, release the chain brake to prevent potential mishaps. Simply move the front handle guard in the direction of the handle.

Step 2: Take Off The Chain Cover

The nuts securing the clutch cover should now be loosened using the socket wrench. Two nuts need to be holding the cover in place.

Remove the lid after the nuts are out of the way. Remove the transporting ring from the bolts if the chainsaw is brand-new. But store it in a secure location. You should put it on a tray for the best results. You will soon require it.

Step 3: Discarding the previous chain

At this stage, gently insert the guide bar all the way into the saw’s back side. Then slightly raise the chain out of the groove. The chain should be freed from the sprocket with a little pressure. Avoid using too much force or the chain can snap. At this point, carefully remove the chain from its location.

Step 4: Sprocket cleaning

You have the opportunity to tidy the area where the chain will go. There won’t be a practical way to wipe the cover once you close it.

Cleaning is an easy process. To remove all the oil or stuck gunk from the sprockets, simply use a thick rag. A finishing nail can be used to clean the oil ports. Everything should clear up with just a little scraping.

Step 5: Putting The New Chain In Place

Next, affix the new chain to the bar. You must begin at the very top of the sprocket. Continue sewing around the top border of the bar after that. From there, run it to the sprocket’s base. When finished, the top edge cutting link’s edges should face forward.

Step 6: Concluding

The procedure is nearly complete. Now all that needs to be done is swap out the clutch cover and put everything back where it belongs. Replace the clutch cover with a fresh one. After that, tighten the nuts. The nuts simply need to be finger-tight to be secure.

The tension adjustment screw can now be turned with the socket wrench and a flat-head screwdriver. To tighten it, turn the screws counterclockwise. Continue to tighten it until the bottom of the chain is completely flat.

Finally, use the wrench to tighten the remaining bolts. And a new chain has been added to your Husqvarna 350 chainsaw.

As you can see, changing the chain on a Husqvarna 350 chainsaw is really simple. However, if you are not attentive enough, things could go wrong. For optimal performance output, you must also make sure the Husqvarna chainsaw has the proper fuel mix ratio.

In addition to harming the equipment, you run the risk of hurting yourself. Try to adhere to the following advice to prevent these unfavorable effects:

These straightforward ideas shouldn’t be difficult to remember. While working, try to imply this, and everything will go swimmingly.

This Video Might Be Useful For You!


What kind of chain will fit a 350 Husqvarna?

The chain should be 0.050 gauge for the 18-inch bar on a 350 Husqvarna chainsaw.

How is the chain of a Husqvarna 350 removed?

Simply separate the cover, insert the guide bar, and lift the chain out of its position to remove the chain from your Husqvarna 350.

Can an Oregon chain be used with a Husqvarna chainsaw?

A Husqvarna chainsaw works great with Oregon chain. The H78 and D72 chain models are the best ones for this.


It’s not as difficult to replace the chain on a Husqvarna 350 chainsaw as you might have thought. And since you already know how to do it, it shouldn’t even take an hour. Just keep the essential safety precautions in place and keep all the tools close at hand.

As you can see, there isn’t much for you to do. This makes the procedure the best course of action. Your money and the chainsaw are both saved.