The Chain on My Poulan Pro Chainsaw Won’t Turn, Move, or Rotate

When the chain on your saw won’t spin or moves slowly, it is imperative that you stop the saw immediately and troubleshoot the problem. Failing to do so might lead to a more serious problem and could harm the components of your chainsaw. It is essential that you halt the saw in the event that the chain on it will not spin or goes very slowly.

If the Poulan Pro chainsaw is being used with the chain brake engaged, the tension is too high, the clutch pads are worn, or the bar and chain are not properly greased, the chain will not spin or move. Another factor is a clutch, damaged clutch pads, or poorly greased bars and chains. Moreover, worn clutch pads might be the cause.

Before you start working with your chain and bar, you need to make sure the saw is switched off and remove the wire from the spark plug. Wait for the machine as a whole to come to a complete stop before putting on any protective gear.

Reasons a Poulan Pro Chainsaw Chain Won’t Turn, Move or Rotate

Chain Brake Activated on a Poulan Pro Chainsaw

The chain brake may be engaged by pulling on the plastic hand guard that is positioned in front of the handle. Here is where the chain brake is located. This protection protects the operator from potential harm if the saw kicks up and back towards them, allowing them to continue working in a risk-free environment.

In the event that anything similar were to take place, the chain brake would immediately engage, preventing the chain from turning in either direction. Also, it stops the chain from moving in the forward direction when it is pushed in that direction.

The chain brake has to be pulled forward by hand whenever the chainsaw is being transported or when it is not being used, both of which are situations in which the chainsaw is not being utilized. This need to be carried out.

Check the orientation of the hand guard to check that it has not been dragged in front of the bike, which would activate the chain brake. It’s likely that you accidentally pushed it forward, which caused the chain to cease travelling in its previous direction. Pulling the guard all the way back to its starting position will allow you to release the brake.

The Poulan Pro Chainsaw I Used Did Not Have Enough Bar and Chain Oil

A decrease in chain speed or complete inactivity will occur from the buildup of friction. Extreme heat and smoke may be produced by this friction, which can be harmful to the bar and the chain.

Use your Poulan Pro at a power setting somewhere between half and three quarters and at a height of roughly a foot above the floor. You can then tell whether the oil level on the bar is sufficient. Watch for a trail of oil to trickle down from the bar after a quarter of a minute. Doing so will indicate that the lubrication is adequate.

If you aren’t getting adequate lubrication, make sure the bar is in great shape and the oil channel isn’t blocked. The oil channel should be cleaned out, and worn or broken guide bars should be replaced.

Always use a high-quality bar and chain oil, such as that offered by Poulan Pro, to ensure the smooth operation of your chainsaw.

The bar and chain oil should be replenished at the same time as the gas tank. This will prevent you from ever being without either one. Important: If the engine oil level is becoming dangerously low, you may not have time to change the gas tank before you run out of chain oil.

Alter the Bar and Chain Oil in Accordance with the Temperature of the Surrounding Air

• • Less viscous oil for use in colder temperatures: Look for oils often sold as low-temperature or winter bar and chain oil.
  • Weight typical for environments with higher temperatures

There is an Issue with the Chain Tension on a Poulan Pro Chainsaw

Since the chain will gradually grow a bit longer as it is used, it is important to adjust it on a regular basis. When the chain is wrapped around the bar too tightly, it will not spin freely.

Set the chain tension so that it may travel freely around the bar of the Poulan Pro chainsaw:

• To turn off the engine, remove the wire from the spark plug.
• Unlatch the chain brake’s lock, and then release it.
• Remove the bar retaining nuts that are holding on the cover that is above the chain brake and the clutch.
• Maintain an upward tilt at the tip of the bar’s nose.
• Turning the tensioning screw in a counterclockwise direction relaxes the chain, while turning it in a clockwise direction causes the chain to become more taut.
• As soon as the desired level of tension is achieved, tighten the bar holding bolts while simultaneously keeping the bar in the nose-up position.

You want the chain to be able to move freely around the bar while yet sitting in a secure position around it. It should not be so slack that it dangles from the guide bar.

Clutch Pads that have seen better days on a Poulan Pro Chainsaw

It is likely that the clutch pads will wear out throughout the course of their lifetime. In the event that anything similar takes place, they will be unable to contact the clutch drum in order to spin the chain. It is important to either repair or replace the clutch assembly in order to continue driving.

Why a Poulan Pro Chainsaw’s Chain Moves at Idle Speed and What You Can Do About It

Modification Is Needed to Be Made to the Carburetor on a Poulan Pro Chainsaw

The chain should not move in any manner while the chainsaw is not being used since it might cause injury. If the chain on your saw moves while you use it, you should make the required adjustments to the saw so that it stops moving.

There is a series of knobs on the carburetor that may be rotated to adjust the air-to-fuel ratio of the mixture. The movement of the chain is affected, in turn, by the idle speed, which is controlled by one of the screws that is labeled “Idle Screw (T).”

Turning the screw counterclockwise until the chain stops moving is the first stage in the process of controlling the idle speed so that it does not move while the engine is running. This ensures that the idle speed does not change.

Chainsaw clutch springs that have seen better days on a Poulan Pro

Poulan Pro chainsaws with centrifugal clutches include springs that retract the clutch weights. As the engine starts to spin faster, centrifugal force will push the weights outward until they hit the drum. Chain moves along bar while drum rotates.

The clutch weights should return to their original position when the engine slows, allowing the chain to cease moving entirely. Maybe the spring that keeps your chain from moving is worn out and has to be replaced if it is still moving.