Fix the Ariens Zero Turn Mower That Won’t Go Forward or Backward!
While a stuck Ariens mower can be a pricey issue, there are various less expensive parts that can wear out or break and make a zero turn immobile.
An Ariens zero turn mower won’t travel forward or backward if activating the manual transmission bypass, pump driving belt is worn, the tensioner pulley is damaged, the idler arm spring is missing or slack, the hydraulic oil is low, old, or heated, or if there is air inside the hydraulic circuit.
Utilizing a hydrostatic transmission, exercise caution. Observe the safety precautions listed in your Ariens driver’s manual. This entails switching off the vehicle’s engine, taking the key out of the ignition, and waiting for all moving parts to cool down.
Table of Contents
7 Causes Of An Ariens Mower’s Inability To Reverse Or Move Forward
On an Ariens mower, the manual transmission bypass is installed incorrectly
An Ariens zero-turn mower has the left and right wheels are powered by two pumps sides. In order for the wheel motors to turn the wheels, the gearbox is made to pump brake fluid to those motors.
The fluid is under such intense pressure that using the bypass lever to move it will be impossible.
When the mower needs to be “free-rolled,” in the bypass position, the transmission’s bypass levers are pulled out. The Ariens’ mechanical issues, where the engine no longer runs, are most likely to blame for this.
Make sure you moved the reverse gear of the bypass transmission position if you previously disengaged the transmission to move the lawnmower mechanically so that the Ariens transmitter can control the wheels.
The bypass levers for the Ariens zero-turn transmission are placed close to each wheel. To disengage the transmission, the lever must be pulled out; to engage the transmission, it must be pushed in.
To use the bypass levers, the mower must be positioned on a level surface with the parking brake applied. When the mower is on a hill, switching the gearbox to switch can make it roll downward.
Ariens Zero Turn Mower Pump Drive Belt Is Worn, Loose, or Broken
An engine-powered v-belt powers the hydraulic pump. An Ariens zero turn won’t work if the belt is unfastened or if it detaches from the pulley.
Make sure the belt is mounted on the pulleys properly and securely. The belt must be replaced if it appears to be worn out, strained, or damaged. Either the idler arm spring or tensioner pulley should be examined if indeed the belt has come off.
A poor tensioner Ariens Zero Turn Mower Pulley
Once you have examined the pump belts and determined that it is not worn, examine the tension pulleys.
This pulley frequently has a bearing in the middle and is constructed of hard plastic. Either the bearing or the pulley could fail. As a result, the belt may either stop turning around the pulley or it may come loose.
Replace any problematic pulley with a fresh one. To ensure that the tensioner arm moves a little but doesn’t seize, keep it lubricated.
Ariens Zero Turn Mower Idler Arm Spring Broken or Worn
The idler spring’s function would be to tighten the driving belt. If the spring is damaged, missing, or strained, it should be replaced.
Ariens Zero Turn Mower: Low Hydraulic Fluid Level or Old Hydraulic Oil
By routinely inspecting and maintaining the transmission as needed, you can ensure that your transmission system is operating at its peak efficiency. The hydraulic fluid and filters must be changed as part of this.
Ariens zero-turn mowers with entry-level models have certain sealed, unserviceable transmission systems. This signifies that the hydraulic oil cannot be changed.
If you are uncertain whether the gearbox on your particular model can be serviced, consult your driver’s manual or seek assistance from an Ariens dealer.
Operating a lawnmower might make the movement seem sluggish if the hydraulic fluid is low or old. It can start out slowly moving or not at all.
When the hydraulic fluid is cool and running low, add more hydro oil until the fluid level reaches the top of the gearbox overflow tanks.
In order to ensure that your fluid level isn’t low due to a leak, it’s a good idea to look for hydraulic fluid leaks.
Remember that after the first following the initial 75-hour break-in period, every 400 hours that, the Ariens hydraulic oil and filters must be changed.
Ariens Zero Turn Mower’s Hot Hydraulic Fluid
It won’t effectively lubricate the hydraulic system if there isn’t enough fluid fluid or if the liquid is outdated or contaminated. As a result of increased friction, the hydraulic fluid may get too hot.
Hot fluid pressure may potentially be a sign of serious transmission damage.
If you have a lawnmower that runs smoothly in the cold but breaks down in the heat, I advise utilizing an Ariens zero turn to reach the dealer.
The gearbox should ideally be checked by a qualified technician to evaluate the extent of the damage and whether a replacement is necessary.
Air in an Ariens Zero Turn Mower’s Hydraulic System
It won’t effectively lubricate the hydraulic system if there isn’t enough fluid fluid or if the liquid is outdated or contaminated. As a result of increased friction, the hydraulic fluid may get too hot.
Hot fluid pressure may potentially be a sign of serious transmission damage.
If you have a lawnmower that runs smoothly in the cold but breaks down in the heat, I advise utilizing an Ariens zero turn to reach the dealer.
The gearbox should ideally be checked by a qualified technician to evaluate the extent of the damage and whether a replacement is necessary.
MORE ABOUT IT Ariens Zero Turn Mower
